Skip to content
barebaricPublic

About

Drivers used by Rayforge

Resources

Stars

0 stars

Watchers

0 watching

Forks

Repository files navigation

raydriver

Rust-native machine drivers for Rayforge, exposed to Python via PyO3.

Currently this provides a full port of Rayforge's advanced GRBL serial driver: character-counting flow control, handshake and status polling, interactive command queue, job streaming with stall detection and deadlock recovery, cancel/safety-shutdown semantics, settings and WCS access, and probe cycles. ESP3D/FluidNC controllers use the same GRBL session over an HTTP command endpoint and WebSocket response channel, with upload-and-execute jobs. Dialects (command templates) remain data owned by Rayforge and are passed in resolved form.

CLI

The raydriver command runs G-code against a real device with live progress, or against the built-in firmware emulator for hardware-free dry runs:

raydriver run job.gcode --port /dev/ttyUSB0 --baudrate 115200
raydriver run job.gcode --emulator          # no hardware needed
raydriver status --port /dev/ttyUSB0 --seconds 5

While a job runs, raydriver run shows acknowledged lines, a progress bar, the device state, machine position, feed rate and ETA; Ctrl-C cancels the job and runs the safety shutdown.

API reference

The Python API reference under docs/api is generated from the .pyi type stubs. Regenerate it after changing the Rust bindings:

make docs

Daemon (remote sessions)

The daemon runs the driver next to the hardware — e.g. on a Raspberry Pi in the workshop — while Rayforge runs on your desk. Jobs run daemon-side and survive client disconnects. Works on Linux, macOS and Windows; full reference in docs/daemon.md.

1. Add your machine

pip install raydriver          # includes network discovery
raydriver scan                 # find your machine's serial port
raydriver daemon add /dev/ttyUSB0

add creates the config file on first use and generates a token — the password clients use to connect. It prints the token; raydriver daemon status shows it again later. The config lives in ~/.config/raydriver/daemon.json (Linux), ~/Library/Application Support/raydriver/daemon.json (macOS) or %APPDATA%\raydriver\daemon.json (Windows).

The daemon announces itself over mDNS, so Rayforge's machine wizard discovers it automatically — no manual network setup.

Defaults are GRBL at 115200 baud; for other firmware use raydriver daemon add PORT --protocol smoothie --baudrate 115200 (protocols: grbl, grbl_simple, smoothie, marlin; ESP3D and FluidNC sessions are configured in daemon.json with their host and HTTP/WebSocket ports). raydriver daemon remove PORT unconfigures a device.

2. Run the daemon

raydriver daemon               # foreground
raydriver daemon install       # or as a service

install uses a systemd user unit on Linux, a launchd LaunchAgent on macOS and a logon scheduled task on Windows. raydriver daemon status shows the service state and probes the daemon; raydriver daemon uninstall stops and removes it.

3. Check it

raydriver list                 # configured devices + connection state
raydriver connection           # connected clients + control lease
raydriver info 127.0.0.1:8765  # sessions, devices and cameras

Connecting clients

Exposing the daemon to the LAN

On loopback the token never leaves the machine, so no TLS is needed. Reaching the daemon from another computer requires a certificate and a non-loopback bind — an exposed listener refuses to start without both a token and TLS. See docs/daemon.md for the setup.

Protocol analyzer

The analyzer captures device traffic, decodes it to a readable listing, and replays or proxies it — the workflow for developing protocols without hardware and for characterizing real controllers. Captures are editable JSONL (text lines or base64 for binary protocols), and decoders plug in per protocol (grbl ships first; raw and hex cover the rest).

# Record a session (or --emulator for a hardware-free dry run)
raydriver analyzer record --port /dev/ttyUSB0 --out cap.jsonl
raydriver analyzer tui --port /dev/ttyUSB0     # interactive monitor

# Print a capture as a decoded listing
raydriver analyzer decode cap.jsonl

# Replay captured frames at a device, at up to Nx speed
raydriver analyzer replay cap.jsonl --to 192.168.1.50:23 --speed 10

# Man-in-the-middle: point an application at the proxy in front of
# a TCP device and record both directions
raydriver analyzer proxy --upstream 192.168.1.50:23 --out mitm.jsonl

Golden tests pin wire behavior: deterministic scenarios run against the firmware emulators, and their decoded listings are diffed against fixtures under tests/golden/ (regenerate with RAYDRIVER_REGEN_GOLDEN=1). Captures from real hardware can be dropped in as fixtures the same way, so protocol changes that alter what goes over the wire fail loudly.

Security policy

Analyzer network endpoints are hardened before any socket opens:

  • listeners bind loopback (127.0.0.1) without authentication by default;
  • non-loopback or wildcard binds require both a token and TLS — there is no override;
  • explicitly configured authentication is never dropped.

Token checks and TLS handshakes are covered by tests that drive the real sockets and assert on the outcomes.

Releases

Releasing mirrors the Raygeo flow:

  1. Configure a PyPI trusted publisher for this repository once (owner barebaric, repo raydriver, workflow release.yml, environment pypi).
  2. gh release create v0.1.0 --title "v0.1.0" --generate-notes

The Build and Publish workflow then stamps the version from the tag, builds wheels (Linux/Windows/macOS) and an sdist, publishes to PyPI via OIDC, and attaches the artifacts to the GitHub release.

Development

make venv && source .venv/bin/activate
make dev     # build + install (do this before testing)
make test    # pytest suite (all tests are Python-based)
make check   # lint + test

Usage

import asyncio
from raydriver.config import GrblSerialConfig
from raydriver.core import SessionEvent
from raydriver.grbl import GrblSession

session = GrblSession(
    config=GrblSerialConfig(port="/dev/ttyUSB0", baudrate=115200),
    dialect={
        "home_all": "$H",
        "home_axis": "$H{axis_letter}",
        "clear_alarm": "$X",
        "laser_on": "M4 S{power:.0f}",
        "laser_off": "M5",
    },
    event_callback=on_event,
)

def on_event(event: SessionEvent):
    match event:
        case SessionEvent.StateChanged():
            print("device state:", event.state.status.name)
        case SessionEvent.ConnectionStatusChanged(status=status):
            print("connection:", status)
        case SessionEvent.RawRx(line=line):
            print("<<", line)
        case SessionEvent.RawTx(line=line):
            print(">>", line)

async def main():
    await session.connect()
    print(await session.execute_interactive_command("$I"))
    await session.disconnect()

asyncio.run(main())

xTool M2

M2Session connects to the M2's WS-V2 service for state monitoring, homing, motion and control of a job already staged on the machine. It does not upload or stream G-code jobs; use xTool Studio to stage those. M2 support uses a reverse-engineered local protocol and has not yet been validated against physical hardware.

The device commonly presents a self-signed TLS certificate. Certificate validation remains enabled by default. Set tls_allow_invalid_certs only on a trusted private network if the device certificate is not trusted by the host:

import asyncio
from raydriver.core import SessionEvent
from raydriver.xtool.m2 import M2Session

async def main():
    connected = asyncio.Event()

    def on_event(event):
        if (
            isinstance(event, SessionEvent.ConnectionStatusChanged)
            and event.status == "CONNECTED"
        ):
            connected.set()

    session = M2Session(
        config={
            "host": "192.168.1.50",
            "tls_allow_invalid_certs": True,
        },
        event_callback=on_event,
    )
    await session.connect()
    await asyncio.wait_for(connected.wait(), timeout=15)
    await session.disconnect()

asyncio.run(main())

The session also exposes home, move_to, jog, start, set_hold and cancel for supported machine-control operations. connect starts the connection loop; wait for the CONNECTED connection-status event before issuing machine commands.

About

Drivers used by Rayforge

Resources

Stars

0 stars

Watchers

0 watching

Forks

Releases

Packages

Contributors

Languages